This teaching system consists of 3 learning boards on the subject of protective measures, installation technology and protection technology. All three topics are important basics for most electrical professions. Especially important are the protective measures according to DIN VDE 0100, which can be taught completely with the safety board. With the electrical installation board, the basic circuits of installation technology can be learned in a practical way on a board. The installation test board is used for measurements in the field of electrical protection technology and installation technology. Both boards are equipped with an error simulation, with which the search for the most common errors can be practiced.
Note: The matching experiment instructions must be ordered separately.
Our products are designed for the European market and meet CE requirements. For international use, regional regulations apply which must be observed. The usability of the products shown must therefore be checked in advance.
The training board Electric Installation is a training concept for setting up and examining the basic circuits of installation technology. Troubleshooting is of particular importance here. Faults can be simulated using a circuit board.
- The most important basic circuits of installation technology on a training board
- Practical experiments through direct use of the mains voltage
- With built-in fault simulation
- No special laboratory tables required, 230 V socket is sufficient
The training board Installation Test is used for measurements in the field of electrical protection and installation technology.
- Practical measurements with commercially available VDE test equipment
- For testing protective measures according to VDE 0100
- For measurements in the 1- and 3-phase system
- With simulation of insulation and loop resistance
- Simulation of frequently occurring faults in protection and installation technology
- Excellent for testing purposes
- Measurement and simulation of earth resistance
With the training board Safety, we offer you a training system that is excellently suited for conducting tests in the field of electrical protective measures.
- All important protective measures according to VDE 0100 in one board
- Built-in power supply, single-phase socket is sufficient
- Optimum safety for the user due to protective extra-low voltage
- Short set-up time, as all accessories are directly integrated in the unit
- TT-network, TN-C-S-network, IT-network possible by reconnection
To carry out experiments, the boards are placed on the table or hung in an A4 experiment rack for demonstration purposes. The boards are also available in a box (see "Matching this").
- Industrial electrician
- Electrical installation technician
- Electronics technician
- Electronics technician, industrial engineering
- Electronics technician, devices and systems
- Electronics technician for automation technology
- Electronics technician for building and infrastructure systems
- Electronics technician for machines and drive technology
- Electronics technician for aeronautical systems
- Mechatronics technician
Training board Safety
- Protection against direct and indirect contact
- Protection by protective low voltage
- RCD residual current device
- Overcurrent protection devices
- Summation current transformer
- Autotransformer
- Protective measures in the TN network
- Protective measures in the TT-Net
- Measuring the grounding resistance
- Protective measures in the IT network
- Protective Insulation
- Protective separation
- Earth Ground
Training board Electrical installation
- S-Shutdown
- Alternate switching
- Cross circuit
- Impulse circuit
- Staircase light circuit
- Dimmer circuit
- Outdoor light with motion detector
- Fault simulation and
- Troubleshooting
Training board Installation test
- Practical measurement with standard VDE test equipment
- Inspection of protective measures according to VDE 0100
- Measurements in 1- and 3-phase network
- Simulation of insulation and loop resistance
- Simulation of frequently occurring errors in protection and installation technology
- Measurement and simulation of the earth resistance
Safety Board
- Mains connection:
- Mains voltage: 230 V AC / 115 V AC (110 V AC)
- Mains frequency: 50 ... 60 Hz; 40 VA
- L1' = 23 V; 1.5 A corresponds to 1/10 of the mains voltage; for safe experimentation
- Dimensions (W x H x D): 532 x 297 x 110 mm
- Weight: approx. 4.5 kg
Installation Test Board
- Mains connection (3-phase):
- Mains voltage: 230/400 V AC
- Mains frequency: 50 ... 60 Hz
- Plug connection: Cekon (CEE standard)
- Dimensions (W x H x D): 532 x 297 x 140 mm
- Weight: approx. 5.5 kg
**Electric Installation Board
- Mains connection (with earthing contact):
- Mains voltage: 220 ... 240 V AC
- Mains frequency: 50 ... 60 Hz
- Power consumption: 30 VA
- Dimensions (W x H x D): 532 x 297 x 130 mm
- Weight: approx. 3 kg
Mechanical specifications:
The front panels of the training boards are made of 5 mm thick laminate, colour matt blue, and are engraved with white switching symbols, corresponding to the built-in function groups. A sturdy plastic cover protects the rear of the unit and its shape allows it to be placed at an angle on the table to suit the work.
- Training board Safety
- Set of cables for the training board Safety
- Training board Electric installation
- Set of cables for electric installation board
- Training board Installation test