With the teaching system "Basic Electronics" we offer a universal teaching and learning system which is perfectly suited for the following experimental groups:
- Direct current, alternating current and three-phase current technology
- Characteristic curves of diodes and transistors
- Characteristic curves of thyristors
- Amplifier circuits
- Bridge Circuits
This teaching system can also be ordered including USB oscilloscope and measurement interface (see "Variants").
Note: The matching experiment instructions must be ordered separately.
Our products are designed for the European market and meet CE requirements. For international use, regional regulations apply which must be observed. The usability of the products shown must therefore be checked in advance.
The teaching system Basic Electronics has, in addition to the power supplies required to carry out the experiments, a large plug-in panel for setting up the experiments with pluggable components. In this plug-in panel, 4 mm safety sockets are arranged in a 19 mm grid. One group of four sockets is electrically connected to each other (marked by white engraving).
- A circuit is built by connecting the individual sockets via connecting plugs or connecting leads and via the pluggable components specified by the circuit.
- Universal teaching and learning system for the basics of electrical engineering and electronics.
- With integrated direct, alternating and three-phase current source and function generator
- Function generator, DC and three-phase current source are short-circuit-proof and monitored by LEDs
- Via the integrated USB interface and the operating software, the output signals of the voltage sources can be precisely adjusted on the PC and simultaneously projected via a connected beamer (not included in the scope of delivery)
- Clear arrangement of the accessories on the printed separate storage plate
- Detailed experiment instructions with solution part (not included in the scope of delivery)
To carry out experiments, the training board is placed on the table or hung in an A4 experiment rack for demonstration purposes.
A storage plate is available for storing the pluggable components. The front of the plate is printed with the circuit symbols corresponding to the components to be plugged in, thus allowing easy and clear storage.
The training board is also available in a box (see "Matching this").
In the box version, the accessory set is mounted in the lid of the box.
- Electronics technician for information and systems technology
- Industrial electrician (appliance and systems)
- Electronics technician
- Electronics technician, industrial engineering
- Electronics technician, devices and systems
- Electronics technician for automation technology
- Electronics technician for building and infrastructure systems
- Electronics technician for machines and drive technology
- Electronics technician for aeronautical systems
- Mechatronics technician
- Electrical circuit / Ohm's law / Kirchhoff's law
- Voltage and current error circuit
- Electrical resistors
- Substitute voltage sources
- Series connection of voltage sources
- Parallel connection of voltage sources
- Electrical power and work
- Efficiency of electrical power
- Voltage, current and power adjustment
- Determination and representation of characteristic values in alternating current technology
- Three-phase alternating current (three-phase current)
- Capacitor in alternating current circuit
- Coil in alternating current circuit
- Interconnection of resistor, capacitor and coil
- Transformer, Transformer
- Diodes / Transistors / Thyristors
- Operational amplifier
- Bridge circuits (Wheatstone Bridge, Thevenin Theorem, Norton Theorem, Maxwell Bridge, Maxwell-Vienna Bridge, Capacitor Measuring Bridge)
- Mains connection:
- Mains voltage: 230 V AC / 115 V AC (110 V AC)
- Mains frequency: 50 ... 60 Hz
- Power consumption: approx. 70 VA
- Direct and alternating voltages:
- DC voltage: +15 V (± 5 %); 800 mA
- - 15 V (± 5 %); 800 mA
- + 5 V; 100 mA
- 0 ... 25 V; 300 mA
- AC voltage: 24 V AC; max. 100 mA
- Function generator:
- Sine / square / triangle: USS = 0 ... 20 V; 100 mA
- f = 1 Hz ... 250 kHz
- Ri = 60
- Square wave, positive: US = 5 V / TTL
- PWM: 10 kHz; pulse width 0 ... 100 %
- DC offset: +12 V ... -12 V
- Three-phase generator:
- Line voltage: 7 Vrms
- Conductor voltage: 12 Vrms
- Conductor current: max. 50 mA
- Frequency: approx. 50 Hz
The outputs of the function generator as well as the DC and three-phase current sources are short-circuit-proof and monitored by LEDs.
- Dimensions:
- PC Basic Electronic training board (W x H x D): 532 x 297 x 120 mm
- Accessory kit for training board (W x H x D): 266 x 297 x 160 mm
- Weights:
- PC Basic Electronic training board: approx. 3.9 kg
- Accessory set for training board: 2.2 kg
Mechanical specifications
The front panel of the training board is made of 5 mm thick laminate, colour matt blue, and is engraved with white switching symbols corresponding to the built-in function groups. A sturdy plastic cover protects the rear of the unit and, due to its shape, allows it to be placed at an angle on the table to suit the work.
- Training board PC Basic Electronics
- Accessory kit for training board
- Cable set for training board