This teaching system consists of 3 training boards on the subject of power electronics. With the Power training board, you receive a demonstration and exercise system with which experiments in the entire field of power electronics can be carried out. With the Motor training board you get a controlled system that can be used in power electronics (Power Board), in control engineering (PID Board) as well as in communications engineering. With the Stepping training board you get a controlled system that can be used in power electronics as well as in digital control technology.
Note: The matching experiment instructions must be ordered separately.
Our products are designed for the European market and meet CE requirements. For international use, regional regulations apply which must be observed. The usability of the products shown must therefore be checked in advance.
Power training board
With the Power training board, we offer you a demonstration and training system with which experiments in the entire field of power electronics can be carried out.
- The entire power electronics in one board
- With built-in three-phase current source
- Plug-in panel for temperature and light control circuit
- All experiments with protective extra-low voltage (12 V)
- Four-quadrant operation with H-circuit (MOS-FET) or antiparallel thyristor bridges
Motor training board
With the Motor training board we offer a controlled system that can be used in power electronics (POWER BOARD), in control engineering (PID BOARD) as well as in communications engineering (PLL).
- Universal speed control system
- Extendable by plug-in module for temperature and light control
- With integrated four-quadrant display
- With variable flywheel mass
- Two-channel angle encoder
- Built-in four-quadrant amplifier
Stepping training board
With the Stepping Board, we offer you a controlled system that can be used in power electronics as well as in digital control technology.
- Universal controlled system for power electronics and digital technology
- Use as synchronous motor and stepper motor
- Digital angle and speed detection via pluggable reflection light barrier
- Digital control inputs for both directions of rotation
- With built-in phase shifter and control logic
- Bipolar and unipolar operation of the stepper motor
To carry out experiments, the training board is placed on the table or hung in an A4 experiment rack for demonstration. The Power Board is also available in a box (see "Matching this").
- Electronics technician for energy and building technology
- Electronics technician for industrial engineering
- Electronics technician for automation technology
- Electronics technician for building and infrastructure systems
- Mechatronics technician
Training board Power
- Experiments on the alternating current network
- Experiments on the three-phase mains
- Experiments on the direct current network
- Experiments with the GTO (gate turn off)
Training board Motor
- Characteristics of the speed controlled system, the servo controlled system and the temperature and light controlled system
- Electronic load
- Torque control
- Speed control
- Voltage control
- Temperature control with various controllers
- Brightness control with various controllers
- Position control
Training board Stepping
- Origin of the rotary motion
- Structure of the electromagnets in the stator
- Control of stepper motors
- Stepping sequence
- Measurements of the internal structure of the stepper motor and the electrical interior of the stepper motor
Training board Stepping and Power
- Stepper motor operation with sinusoidal current
- Speed and rotational frequency with sinusoidal motor current
Power training board
- Mains connection:
- Mains voltage: 230 V AC / 115 V AC (110 V AC)
- Mains frequency: 50 ... 60 Hz
- Power consumption: approx. 80 VA
- Mains switch: ON / OFF, with control lamp
- Dimensions (W x H x D): 532 x 297 x 130 mm
- Weights: approx. 5.4 kg
Motor training board
- Mains connection:
- Mains voltage: 230 V AC / 115 V AC (110 V AC)
- Mains frequency: 50 ... 60 Hz
- Power consumption: approx. 20 VA
- Mains switch: ON / OFF, with control lamp
- Dimensions (W x H x D): 266 x 297 x 90 mm
- Weights: approx. 2.2 kg
Stepping training board
- Mains connection:
- Mains voltage: 230 V AC / 115 V AC (110 V AC)
- Mains frequency: 50 ... 60 Hz
- Power consumption: approx. 20 VA
- Dimensions (W x H x D): 266 x 297 x 1100 mm
- Weight: approx. 1.2 kg
Mechanical specifications:
The front panel of the training board is made of 5 mm thick laminate, colour matt blue, and is engraved with white switching symbols, corresponding to the built-in function groups. A sturdy plastic cover protects the back of the unit and, due to its shape, allows it to be placed at an angle on the table to suit the work.
- Training board Power
- Cable set
- Training board Motor
- Training board Stepping