The teaching system for basics of electrical engineering/electronics without PC support provides you with everything you need to teach the basics of electrical engineering, electronics and analogue technology. The teaching system has a function generator, various voltage sources and a large plug-in panel for setting up the experiments. The clear arrangement and detailed experiment instructions ensure efficient learning.
This teaching system can also be ordered including USB oscilloscope and measurement interface (see "Variants").
Note: The matching experiment instructions must be ordered separately.
Our products are designed for the European market and meet CE requirements. For international use, regional regulations apply which must be observed. The usability of the products shown must therefore be checked in advance.
In addition to the power supplies required to carry out the experiments, the PC Electronic training board has a large plug-in field for setting up the experiments with pluggable components. When setting up a circuit, the individual sockets are connected via connecting plugs or connecting leads and via the pluggable components specified by the circuit. The patch panel is also suitable for connecting leads with 4 mm safety plugs and rigid sleeves. By additionally using the optionally available measuring interface incl. visualisation software (see "Matching this"), the measured data can be easily displayed virtually on the PC monitor.
- Universal teaching and learning system for the basics of electrical engineering, electronics and analogue technology
- With integrated DC, AC and three-phase current source and function generator
- Function generator, DC and three-phase current source are short-circuit-proof and monitored by LEDs
- Via the integrated USB interface and the visualisation software, the output signals of the voltage sources can be set on the PC and simultaneously projected via a connected beamer (not included in the scope of delivery)
- Clear arrangement of the accessories on the printed separate storage plate
- Detailed experiment instructions with solution section (not included in the scope of delivery)
Can be used with or without PC support.
To carry out experiments, the PC Electronic Board is placed on the table or hung in an A4 experiment rack for demonstration purposes. A storage plate is available for storing the pluggable components. The front of the plate is printed with the circuit symbols corresponding to the components to be plugged in, thus allowing easy and clear storage. The PC Electronic Board is also available in a box (see "Matching"). In the box version, the accessory set is mounted in the lid of the box. The individual electrical components are wired via 2- and 4-mm sockets.
- Electronics technician for information and systems technology
- Industrial electrician (appliance and systems)
- Electronics technician
- Electronics technician, industrial engineering
- Electronics technician, devices and systems
- Electronics technician for automation technology
- Electronics technician for building and infrastructure systems
- Electronics technician for machines and drive technology
- Electronics technician for aeronautical systems
- Mechatronics technician
With the teaching system basics of Electrical Engineering/Electronics we offer a universal teaching and learning system that is excellently suited for the following experimental groups:
- Direct, alternating and three-phase current technology
- Characteristic curves of diodes and transistors
- Characteristic curves of thyristors and triacs
- Amplifier circuits
- Oscillator circuits
- Modulators and Demodulators
- Flip-flops
- Power supply circuits
- Switching voltage regulator and DC/DC converter
- Circuits of power electronics
- Mains connection:
- Mains voltage: 230 V AC / 115 V AC (110 V AC)
- Mains frequency: 50 ... 60 Hz; 40 VA
- Power consumption: approx. 70 VA ...
Direct and alternating voltages
- DC voltage:
- +15 V (± 5 %); 800 mA
- -15 V (± 5 %); 800 mA
- +5 V; 100 mA
- 0 ... 25 V; 300 mA
- AC voltage:
- 24 V AC; max. 100 mA
Function generator
- Sine / square / triangle:
- USS = 0 ... 20 V; 100 mA
- f = 1 Hz ... 250 kHz
- Ri = 60
- Square wave, positive:
- US = 5 V / TTL
- PWM:
- 10 kHz; pulse width 0 ... 100 %
- DC offset:
- +12 V ... -12 V
Three-phase generator
-
Line voltage: 7 Vrms
-
Conductor voltage: 12 Vrms
-
Conductor current: max. 50 mA
-
Frequency: approx. 50 Hz The outputs of the function generator and the DC and three-phase source are short-circuit-proof and monitored by LEDs.
-
Dimensions (W x H x D): 532 x 297 x 120 mm
-
Weight: approx. 3.9 kg
Mechanical specifications:
The front panel of the training board is made of 5 mm thick laminate, colour matt blue, and is engraved with white switching symbols corresponding to the built-in function groups. A sturdy plastic cover protects the rear of the unit and, due to its shape, allows the unit to be placed at an angle on the table in a way that is suitable for work.
- Training board PC Electronic
- Accessory kit for training board
- Cable set for training board