Combi Set: Electrics and Electromagnetism
English

Plug-in element system for students

Clearly arranged: with correct circuit paths and symbols

Our unique plug-in element system with the corresponding boxes provides an extremely clear way to carry out experiments in the field of electrics or electronics. Both the individual plug-in elements and the individual boxes are printed with clearly visible switching paths and symbols. In this way, the students learn directly and intuitively the correct circuit diagrams and can reproduce them correctly at any time. The predefined position of the plug-in elements makes it easy for the students to implement the corresponding circuits. They can concentrate fully on the physical principles during assembly.

Countless: Combinations with our boxes

With the help of the different boxes and the numerous plug-in elements, a wide variety of experiments can be realized: From basic simple circuits to complex electronic circuits The experiment instructions (available separately) include comprehensive and didactically sequenced instructions for the individual experiments.

Magnetic: as a demonstration experiment

The additionally available magnetic base plate also makes it possible to use the box system and the plug-in elements as demonstration experiments on a magnetic board. By using the same system for demonstrations on the board and the student experiments, the students can understand the interrelationships much more easily.

Case electrics/electronics - devices and body parts:

• 2 x Plug-in element lamp socket E10
• 2 x Plug-in element switch ON/OFF
• 2 x Plug-in element battery holder (baby)
• 2 x Plug-in element resistor 100 Ω
• 1 x Plug-in element resistor 500 Ω
• 1 x Plug-in element resistor 1 kΩ
• 1 x Plug-in element resistor 10 kΩ
• 1 x Plug-in element variable resistor 10 kΩ
• 2 x Plug-in element connector plug with socket
• 2 x Plug-in element connecting plug
• 2 x Terminal plugs, set
• 1 x Electrolyte trough with separating sieve
• 2 x Holder with hole
• 2 x Holders with slot
• 1 x Conductor and non-conductor, set
• 1 x Bimetal strip
• 1 x Set of electrodes
• 2 x Crocodile clips with plug pin
• 1 x Crocodile clip blank
• 1 x Plug-in element PTC resistor
• 1 x Plug-in element NTC resistor
• 1 x Plug-in element LDR resistor
• 2 x Plug-in element LED red
• 1 x Plug-in element Si diode
• 1 x Plug-in element Z-diode
• 1 x Plug-in element capacitor 100 μF
• 1 x Plug-in element capacitor 1000 μF
• 1 x Plug-in element transistor NPN, left base
• 1 x Plug-in element summer
• 1 x Plug-in element resistor 47 Ω
• 1 x Plug-in element potentiometer 470 Ω
• 1 x Fuse wire, D = 0.1 mm, roll, red
• 1 x Resistor wire, D = 0.2 mm, roll, blue
• 1 x Copper wire, D = 0.2 mm, roll, black
• 2 x Incandescent lamps E10, 1.5 V/50 mA
• 2 x Incandescent lamps E10, 6 V/50 mA
• 1 x Incandescent lamp E10, 6 V/0.5 A
• 1 x Bulb E10, 6 V/2,5 A
• 4 x Connecting cables red/black, 4 mm-plug
• 4 x Connecting leads red/black, safety plug

Dimensions: 53 x 40 x 12,5 cm (W x D x H)

Case electromagnetism - devices and assembly parts:

• 2 x Coil 500 turns
• 1 x Coil 1000 turns
• 1 x U-core, bladed, with yoke and tension screw
• 1 x Lamp socket E 10 with plug, blue
• 1 x Bar magnet, neodymium, 60 x 18 x 18 mm
• 1 x Clapper
• 1 x Bell bowl
• 4 x Flat plugs
• 1 x Mounting plate for U-core
• 1 x Rotor coil
• 1 x Iron core for rotor
• 1 x Commutator
• 1 x Brush holder, pair
• 1 x Wire brushes, pair
• 1 x Pointer
• 1 x Lamp socket E 10, yellow, for rotor coil
• 1 x Magnet holder, pair
• 2 x Block magnet, neodymium, 18 x 18 x 10 mm
• 1 x Support plate for bar magnet
• 1 x Screw, long, black head
• 1 x Screw, short, blank head
• 1 x Plate with hook
• 1 x Plug with hook
• 1 x Plug element lamp socket E 10
• 1 x Plug element switch ON/OFF
• 2 x Connecting plugs
• 4 x Bulb E10

Clearly and safely sorted in plastic case with foam insert

Dimensions: 45 x 33 x 11 cm (W x D H)

Box set - electrical electronics - plug-in element system:

• 1 x Circuit box
• 1 x Switch box
• 1 x Universal plug box
• 1 x Bell box
• 1 x Relay box
• 1 x Motor box
• 1 x Transformer box
• 1 x Transistor box

Supplementary equipment set with contact box:

• 1 x Contact box
• 1 x Tare weight on connector
• 1 x Additional weight
• 1 x Distributor bridge
• 1 x Conductor loop on plug
• 2 x Bearing bolts
• 1 x Bilge ring on rod
• 1 x Waltenhofen plate
• 1 x Eddy current plate with extension
• 1 x Eddy current ring
• 2 x Rod with plug

One student workbook each for electrics and electronics Plug-in element system.